ASTM D – Air Permeability of Textile Fabrics . ASTM E testing covers a pin-type bearing test of metallic materials in order to determine bearing yield. Find the most up-to-date version of ASTM E at Engineering ASTM E covers the standard test method for pin-type bearing test of metallic materials. The ultimate strength and yield strength of a bearing material are.
|Published (Last):||11 December 2018|
|PDF File Size:||14.72 Mb|
|ePub File Size:||11.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
These test standards cover procedures for testing untreated paper used for electrical insulating purposes. This test standard determines the quasi-static longitudinal tensile strength and elongation properties of fiber reinforced polymer matrix composite bars commonly used as tensile elements in reinforced, prestressed, or post-tensioned concrete.
This test standard determines the in-plane shear response of polymer matrix composite materials reinforced by high-modulus fibers. This standard describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher than the modulus of the adhesive.
The bearing material used in this test is a flat piece with a centered astn and near the edge. This test standard covers the determination of the resistance-to-peel strength of an adhesive bond between one rigid adherend and one flexible adherend when tested at an angle of approximately This test standard determines the transverse compressive properties of wound polymer matrix composites reinforced by high-modulus continuous fibers.
These test standards cover the tensile testing of aramid yarns, cords twisted from such yarns, and fabrics woven from such cords. This test standard covers the determination of the mechanical properties of plastic lumber and shapes, when the entire cross-section is loaded in compression at relatively low uniform rates of e2338 These ashm standards cover the measurement of the peel adhesion of pressure-sensitive tapes by testing the adherence, when peeled at This standard describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.
This test covers the determination of the comparative shear strengths of adhesives for bonding metals when tested on a standard specimen and under specified conditions of preparation and testing at This standard covers the measurement of tensile e328 of geotextiles using a wide-width strip specimen tensile standard.
ASTM E238 Bearing Strength of Pins Test Equipment
These test standards cover the procedures for testing copper-clad laminates produced from fiber-reinforced, thermosetting polymeric materials intended for fabrication of printed wiring boards. Exova, the global testing, calibration and advisory services provider, has been given approval by Airbus to conduct ASTM E Bearing testing of metallic materials for the aircraft manufacturer and its supply chain.
This test covers the determination of the comparative properties of either metal or wood adhesive bonded assemblies when subjected to flexural stresses with standard shape specimens and under defined conditions This test standard covers the procedure for testing the tensile breaking strength of the perforations in one-part continuous forms.
This test standard is used to measure the strip tensile properties of reinforced geomembranes. This test standard covers the determination of the force required to ravel a yarn from the edge of a loop pile, tufted, carpet. This test standard describes the determination of interlaminar fracture toughness, Gc, of continuous fiber-reinforced composite materials at various Mode I to Mode II loading ratios using the Mixed-Mode Bending Test.
This test standard employs the grab procedures used to determine localized weakness due to bar-tacking in the pocket areas of all types of garments such as shirts, including the side This specification covers the requirements for continuous fiber and staple fiber glass strands, including single, plied and multiple wound.
Fixtures conform to ASTM – Grip-Engineering
These test standards cover the testing of cords made from steel for use in the reinforcement of pneumatic tires and may be used to test similar cords or filaments used This test standard covers the determination of the load required to rupture a leather test specimen having a. This test procedure covers the measurement of the force required to pull a tuft completely out of a pile yarn floor covering sample.
This standard provides guidelines for hand holes in corrugated boxes during manual handling of boxed cargo. This test standard covers the determination of the force required to disengage snap fasteners by a pull perpendicular to and parallel with the plane of the snap fastener. The yarn or cord may be wound on cones, Procedures are specified for determining the damage resistance This test standard covers the determination of the tear resistance of flexible plastic film and sheeting at very low rates of loading, 51 mm 2 in.
This test standard covers the determination of the flexural properties of fiber-reinforced pultruded plastic rods. This standard covers the determination of the relative peel resistance of adhesive bonds between one rigid adherend and one flexible adherend when tested under specified conditions of preparation and testing.